Monday

milk carton holder using hougie board

I have been asked by some of my docraft buddies how to make one of these for some time now.

They will be pleased to know I have finally gotten around to it

This tutorial is for the the holder that will fit four of these milk cartons in it.

For this tutorial I am using my hougie board for speed but you could quite easily use a ruler and a scoring tool and just follow the measurements given
Cardseock you will need:
2 pieces measuring 20.5 cms x 13.5 cms
2 pieces measuring 29.5 cms x 14.5 cms
1 piece measuring 15 cms x 14.5 cms

 Take the 2 pieces measuring 20.5 cms x 13.5 cms and score/fold
around all four sides at 3cms


Trim a little notch as shown from all four corners ( the same as you would to make a box)


 Place adhesive on the corner tab and secure and shown to make your "box"

 Repeat for both pieces and you will end up with 2 boxes, as shown below

For me a strong wet glue is a must as it bonds the fibres of the card together . I know some people will recommend the super sticky red backed tape and I have used this in the past. However I always go back to a wet glue because I find I need a little more flexibility when fixing things. With a tape once it's stuck it's stuck, with a wet glue you have a few seconds to manoeuvre things into place. I suppose the one downside is that you do have to use something to hold it in place whilst you wait for it to dry, as I have below but if you use a quick drying glue then it should really only be a couple of minutes...Just my personal choice of course, do whatever suits you.

Here is what you should end up with times 2


So while I wait for my "boxes" to dry we'll move on to the handle

For this tutorial I am cutting my hole for the handle with a circle nestability
You could use an oval or any large punches you may have

Take the two pieces of cardstock measuring 29.5 cms x 14.5 cms
( As you can see I have rounded off the top corners using a papermania punch but you could omit this step if you wish)

As shown below, make a pencil mark at the top measuring in around 1.5 cms and another a few centimetres further down marking the center point of the width (7.25cm) This does not have to spot on as we are only using it as a guide for placing the nestie or punch used for cutting our handle


We need to cut both pieces of card at the same time to get perfect alignment for the handle holes so
lay one piece of card on top of the other , ensuring that they stay perfectly aligned at all times .( I find keeping them aligned quite easy but you could secure with a piece of very low tack tape)
( you must also remember at this point that if you are using a patterned or textured cardstock
to place the two patterned or textured sides facing outwards)

( if you are using a punch , simply punch your first piece, lay that ontop of the other peice (perfectly aligned) draw around the punch out and line your punch up with the lines when you punch)

Place you nestability as shown in the picture .
But the edge up to the mark you made 1.5cms from the edge
and use the central mark as a guide to get your cut central.


 You should end up with 2 pieces like this

 Place you nestie under the right side of the cardstock and embossing with a ball tool
( I find this easier than faffing trying to put them back through the diecutter especially with such a simple shape as this)


Now score/fold both pieces as shown at 7.5 cms from the bottom

Now we are ready to assemble
Cover the small section at the bottom with adhesive


 and place inside the box as below

 smooth down with a bone folder or similar

(boy don't my hands look fat) lol

Place some more adhesive down along the back panel where the base meets the handle 

repeat for the second side and you should have this


now we join them together

cover the back of one half in adhesive and join together as shown


you should end up with this



now for the final step 
Cover the bottom of you holder with glue
and adhere the last piece of card measuring 15 cms x 14.5 cms

 this is the part which adds all the strength and stability to the design

 And that's it!  you can now decorate as you wish

And voila in true blue peter sytlee..here's the one I made earlier lol


All I did to this one was add four thin strips of stamped card along the edges of the "boxes"
I would probably always do that because it hides the join (see below)
And a couple of stamped images cut out with nesties


I hope this tutorial has been of use to you and is understandable.
But as always, if there is anything you are struggling with and need help
please feel free to either chatbox me or email me (from my profile)
TFSB
Kerry x

Well after all that it just suddenly popped into my head this morning that why didn't I just make the bottom tray out of one piece of card?? doh!
1 piece of card measuring 20.5 x 21 cm score all the way around at 3cms and cut and assembled as shown above (like you would a box)?
The above tut works perfectly well of course but it is much less time consuming and a bit neater with just the one piece. I will edit this post at a later date :)

 

Thursday

Milk carton on the hougie board

After I posted this little set a lot of people asked me if I could do a little tut
on how I make the milk cartonson the hougie board


So here it is

What you will need
A4 piece of card 
hougie board
adhesive
bull dog clip


 Place you piece of A4 card on your hougie board in a landscape position on the cm side
and score at
7cm 14cm 21cm 28cm
also make a small score approx 3cm long at 10&1/2cm and 24&1/2 cms


 Then turn your card 90 degrees clockwise into portrait position
and score at
6cm 14cm 19&1/2 cms

Fold all the full score lines
and trim away the areas shown above

 You are left with this
Add adhesive down the flap on the right hand side. 
I always use DST and add a few dabs of wet glue on top

Join the side as shown here

 you now have this

 
Fold in the bottom flaps and adhere as above
( again I use DST with a few dabs of wet glue)

This is where those two little scores come in so handy
Simply squeeze the top together on both sides
and clip the top together with your bulldog clip


At this point I run my fingernail/bone folder/embossing tool  down the creases to sharpen

And here's what you end up with
Decorate as you wish

I have also made a holder for 4 of these using my own measurements like here
I will post a tut on that at a later date
TFSB
Kerry x